Whether a cable is installed in a tray, a duct, a conduit or buried directly changes almost everything about the correct choice: the current it can carry, the mechanical protection it needs, the fire performance required and the way it is supported. Installation method is not an afterthought to cable selection; it is one of the inputs that determines it. This guide explains the four main installation environments, how each affects ampacity and construction, what the common site mistakes are, and how to specify a cable for the route it will actually follow. Six answers follow on derating, duct fill, burial depth and support spacing.
In free air on a tray or ladder, a cable dissipates heat relatively well, and the current rating is the highest of the common methods. Cables are usually spaced or grouped, and grouping reduces the rating because the cables heat each other. The tray also provides mechanical support, so the cable does not need armour for its own weight.
In a conduit or duct, the cable is enclosed and the air around it is restricted, so heat dissipation is poorer and the rating is lower. Fill ratio matters: a duct packed with cables cannot dissipate heat, and the derating can be severe. Pulling tension during installation also affects the choice, since a long duct run with bends requires a cable that can withstand the pull.
Buried directly, the cable is surrounded by soil, which conducts heat better than air in some conditions and worse in others. The rating depends on soil thermal resistivity, burial depth and the presence of other cables. Direct buried cable needs mechanical protection against stones, digging and rodents, which is why armoured constructions are common.
In a cable trench with sand bedding and covers, the conditions are between duct and direct burial. The trench provides some protection and some thermal mass, and the rating depends on the trench geometry and the number of circuits.
Each environment also changes the fire requirement. A tray in a public building needs flame retardant performance; a buried cable may not need it at all, though the site rules may still require it.
The first effect is ampacity. The same cable can carry a markedly different current depending on whether it is in free air, in a duct or buried. A designer who sizes from a free air table and installs in a duct creates an overloaded cable, and the failure appears as insulation degradation after a few years rather than as an immediate fault.
The second effect is mechanical. A cable pulled through a long duct with bends experiences tension and sidewall pressure, and a heavy armoured cable may exceed the permitted pulling force. The installation method therefore constrains the construction, not just the size.
The third effect is water. Ducts fill with water, and buried cables sit in wet soil. Water blocking and suitable sheathing become requirements rather than options, and terminations must be suitable for a wet environment.
The fourth effect is maintenance and replacement. A cable in a duct can be replaced by pulling a new one; a directly buried cable requires excavation. The first cost may be higher for the duct, but the lifecycle cost is often lower, and this trade-off is worth calculating rather than assuming.
The fifth effect is regulatory. Many codes prescribe installation methods, burial depths and protection requirements, and a route that ignores them may be non compliant even when the cable is correct.
State the installation method in the enquiry, and be specific: in tray with other cables, in a 100 mm duct at 1 metre depth, directly buried at 0.8 metres in sandy soil, in free air spaced on ladder. Each of those leads to a different derating and possibly a different construction.
State the grouping. The number of cables in the tray or duct and whether they are all loaded determines the derating. A buyer who says in tray without saying how many cables will receive a rating that may not apply.
State the environment: indoor, outdoor, wet, corrosive, exposed to sunlight, subject to mechanical damage. Each factor narrows the construction, and a supplier who knows the environment can propose the right sheath and armour.
Confirm the pulling conditions. For long duct runs, state the length, the number of bends and the available pulling force. This determines whether the cable needs a low friction sheath, whether the conductor class should be finer and whether the installation needs intermediate pull points.
Finally, check the accessories and the supports. Tray spacing, gland types, and the termination environment all follow from the installation method, and they are as much part of the specification as the cable. Products such as the N2XY 4x95mm2 Oxygen-Free Copper PVC Insulated Multi-core Power Cable 0.6/1kV Power Station and the VGV 3x2.5mm2 Rigid Oxygen-Free Copper PVC Insulated Sheathed Electrical Wire 1kV Industrial show how the same conductor size is offered in constructions suited to different routes, from tray installations to armoured buried cable.
Tray spacing is determined by the cable weight and the permitted sag, and by the fault current if the tray also carries earthing duty. Cables should be spaced where the rating depends on it, and where they are grouped, the derating factor must be applied to every cable in the group, not only to the one being sized.
The order of cables on a tray matters in some designs: power cables and signal cables should be separated, or a barrier used, to avoid interference. Where a screened cable is used, the screen must be earthed at the correct points, and the tray itself may need bonding to provide a reference.
In ducts, the number of cables and the number of loaded cables both matter. A duct containing four cables of which two are spares can be rated on two loaded cables, but the spares still occupy space and affect heat dissipation. Designers sometimes forget this, and the result is a duct that runs hotter than calculated.
Direct burial requires attention to depth, bedding and protection. A cable laid on sharp stones will be damaged by the weight of backfill, so a sand bedding and a protective cover are standard. Warning tape above the cable reduces the risk of damage during later excavation, and marker posts at changes of direction help maintenance.
Depth is set by the code and by the risk of disturbance. In areas subject to digging, deeper burial or a concrete slab is used. In agricultural land, depth must exceed the ploughing depth, or the cable will be damaged within a season.
Thermal resistivity of the soil affects the rating, and it varies with moisture content and with the material. Dry sand is a poor conductor of heat; wet clay is much better. A route that crosses both will have sections with different ratings, and the design should use the worst case along the route rather than an average.
A cable in a tray in a public building is exposed to fire from other cables and from the space, and flame propagation along a tray is a recognised route for fire spread between floors. This is why tray installations in public buildings usually require flame retardant cable to a defined test category, and why the tray itself may need fire barriers at floor penetrations.
A buried cable has a different exposure. Fire from outside is unlikely, and the requirement is usually limited to the building entry and to the switch room. Specifying fire resistant cable for the whole buried route is a cost that is rarely justified.
A cable in a duct between buildings sits between the two cases. The duct limits oxygen and limits spread, but a fire in a duct can be difficult to access. Many specifications require flame retardant performance for duct routes as a precaution, and the requirement should be checked rather than assumed.
Before selecting cable, confirm the route type, the grouping, the environment, the pulling conditions and the protection required. Those five answers set the rating, the construction and the accessories.
Stating those details in the enquiry produces a quotation that can be installed as designed, rather than a cable that is correct on paper and marginal on site.
Before the cable is pulled, check the route for sharp edges, the condition of the duct, the number of bends and the presence of other services. Most installation damage is caused by the route rather than by the cable, and a short inspection before pulling prevents the damage that would otherwise be discovered years later.
After installation, confirm the cable is supported at the specified spacing, that the glands are correctly made and that the bending radius has been respected at every change of direction. These checks take an hour and they are the difference between an installation that meets its rating and one that has a hidden weakness.
Record the as installed route, including the positions of joints and the depths of buried sections. That record is what allows future work to avoid the cable, and its absence is the reason so many cables are damaged by later excavation.
Free air with spaced cables. Duct and buried installations are lower because heat dissipation is poorer.
The proportion of the duct cross section occupied by cables. It is limited to allow pulling and heat dissipation, commonly to around one third to one half depending on the standard.
It depends on the code and the protection provided. Typical depths are 0.6 to 1.0 metres, with sand bedding, covers or tiles and warning tape.
Usually not, because the tray provides mechanical support. Armour is more relevant to buried or exposed routes.
Cables close together heat each other, so the rating falls as the number of loaded cables rises.
No. Ampacity, protection and sometimes construction all change, so the design must be recalculated.
The installation environment determines ampacity, mechanical protection, water resistance and fire performance, and it must be stated in the enquiry rather than assumed. Describe the route, the grouping, the environment and the pulling conditions, and confirm the accessories and supports. Shanghai Shenghua Cable Group quotes PVC insulated cable for tray, duct, conduit and direct burial installations, with the current rating and construction suited to the stated method, and it will advise where armour or water blocking is needed. Send your route details through our contact page and our engineers will confirm the specification. Related items include the 2 core 240mm XLPE Insulated Power Cable Copper Conductor , Armored Electric Cable 0.6/1KV, the NYM 3x2.5mm2 UV Resistant PVC Insulated Cable Outdoor Lighting 450/750V IEC60228, the IP68 Waterproof PVC Insulated Power Cable 0.6/1kV 4x25mm2 Underground Direct Burial Copper, the VGV 3x4mm2 UV Resistant PVC Insulated Cable Outdoor Overhead 0.6/1kV IEC60502 Copper, the 0.6/1KV Underground Armored PVC Insulated Cables -20C To 70C For Underground Power Distribution Solutions and the VDE Standard PVC Insulated Cables In Black For Household Electrical Installations.
Most installation damage originates in the route, not the cable, and a short inspection before pulling prevents it.
Recording the as installed route protects the cable from later excavation and simplifies maintenance.
Both habits cost little and return a great deal.
The right cable in the wrong environment is still a wrong cable, and the installation method is the environment that matters most.
Describing the route accurately at enquiry stage is the cheapest engineering decision available.
Accurate information at the enquiry stage is what allows the supplier to quote a cable that will still be correct once it is installed.